DIY chest plate MKIII

The place for general talk about gun, shooting, loading, camping, survival, and preparedness related tools and gear, as well as gear technology discussion, gear reviews, and gear specific "range reports" (all other types of gear should be on the back porch).
Precision
Posts: 4580
Joined: Wed Aug 20, 2008 6:01 pm

DIY chest plate MKIII

Post by Precision » Tue Jun 26, 2012 5:10 pm

we just got some much better steel for MKIII version.

I am so excited. My local sheet metal vendor had 304 stainless and 316L stainless at roughly 40% less than I could get it online (in small quantities) without even factoring in shipping costs.

a 10"x12" sheet was $10 for the 304 and $20 for the 316L at 14 ga (.0747"). I haven't put it on the micrometer, but I think the stuff I got is much more like 12ga (.1046)

We are going to do the sandwich idea again. The 316L will be in the middle and the 304 will be the final stopper.

More testing photo's in a couple of weeks.

The new design is roughly 1.5 inches thick or about an inch thinner than MKII.

Does anyone know the true brinell for these two steels.
I am finding 304 listed as anywhere between 115 and 175
with 316L listed as anywhere from 170 to 265.
Those are some pretty big spreads and I don't see any mention of partial hardening like 301 stainless has. 301 stainless (or similar in high carbon) is what we really wanted but not paying the price ($100 per square foot) for full hardened 301.
"Those who hammer their guns into plows will plow for those who do not." ~Thomas Jefferson
My little part of the blogosphere. http://blogletitburn.wordpress.com/

User avatar
Aglifter
Posts: 8212
Joined: Tue Aug 19, 2008 12:15 am

Re: DIY chest plate MKIII

Post by Aglifter » Tue Jun 26, 2012 5:33 pm

Stainless varies tremendously in quality - if its ChiCom, who knows what you actually are getting...
And for the support of this Declaration, with a firm Reliance on the Protection of Divine Providence, we mutually pledge to each other our lives, our Fortunes, & our sacred Honor

A gentleman unarmed is undressed.

Collects of 1903/08 Colt Pocket Auto

Precision
Posts: 4580
Joined: Wed Aug 20, 2008 6:01 pm

Re: DIY chest plate MKIII

Post by Precision » Tue Jun 26, 2012 5:54 pm

Aglifter wrote:Stainless varies tremendously in quality - if its ChiCom, who knows what you actually are getting...
There is that. I don't know where this is sourced from.
"Those who hammer their guns into plows will plow for those who do not." ~Thomas Jefferson
My little part of the blogosphere. http://blogletitburn.wordpress.com/

User avatar
Combat Controller
Site Admin
Posts: 4887
Joined: Thu Aug 14, 2008 12:03 am

Re: DIY chest plate MKIII

Post by Combat Controller » Tue Aug 14, 2012 10:28 am

I bet this will fit in a vest though....

Still, if you can do it for $20 then you are really on to something! I can't wait to hear more. I wish I had the time to play around with stuff these days...
Winner of the prestigious Автомат Калашникова образца 1947 года award for excellence in rural travel.

Precision
Posts: 4580
Joined: Wed Aug 20, 2008 6:01 pm

Re: DIY chest plate MKIII

Post by Precision » Wed Aug 15, 2012 1:31 am

CombatController wrote:I bet this will fit in a vest though....

Still, if you can do it for $20 then you are really on to something! I can't wait to hear more. I wish I had the time to play around with stuff these days...

We are currently defeating 7.62 x54 steel core without needing an additional spall liner although we are now where near 5#. At a cost of about $30 for non-scrounged items
"Those who hammer their guns into plows will plow for those who do not." ~Thomas Jefferson
My little part of the blogosphere. http://blogletitburn.wordpress.com/

User avatar
Steamforger
Posts: 2784
Joined: Mon Aug 18, 2008 5:41 pm

Re: DIY chest plate MKIII

Post by Steamforger » Fri Feb 13, 2015 2:09 am

Necro'ing for the purposes of leaving this here.

TL;DR/DW- matrix of thin sheet steel, fibreglass, and marbles held with epoxy defeats multiple shots from AK 47.

Precision
Posts: 4580
Joined: Wed Aug 20, 2008 6:01 pm

Re: DIY chest plate MKIII

Post by Precision » Fri Feb 13, 2015 3:52 am

Just goes to show, they can ban "armor" but any fool with a little bit of knowledge can kludge together functional armor from household products.

My design is way more durable then that stuff, but that would take minutes (minus set time) to make.

the only real issue would be the weight penalty vs commercial armor.
"Those who hammer their guns into plows will plow for those who do not." ~Thomas Jefferson
My little part of the blogosphere. http://blogletitburn.wordpress.com/

User avatar
Yogimus
Posts: 4922
Joined: Mon Apr 18, 2011 6:32 am

Re: DIY chest plate MKIII

Post by Yogimus » Fri Feb 13, 2015 8:00 am

One I have seen work well was a 3 layer "BB" with the balls neatly arranged, with a backer and a steel front

User avatar
randy
Posts: 7338
Joined: Wed Aug 13, 2008 11:33 pm
Location: EM79VQ

Re: DIY chest plate MKIII

Post by randy » Fri Feb 13, 2015 1:37 pm

Yogimus wrote:One I have seen work well was a 3 layer "BB" with the balls neatly arranged, with a backer and a steel front
Add a sheet of C4 to the backer and you have a emergency/kamikaze claymore ready to go! :mrgreen:
...even before I read MHI, my response to seeing a poster for the stars of the latest Twilight movies was "I see 2 targets and a collaborator".

User avatar
Lokidude
Posts: 2159
Joined: Tue Aug 19, 2008 2:49 am

Re: DIY chest plate MKIII

Post by Lokidude » Sun Feb 15, 2015 6:46 am

Precision wrote:
Aglifter wrote:Stainless varies tremendously in quality - if its ChiCom, who knows what you actually are getting...
There is that. I don't know where this is sourced from.
Almost guarantee it's Japanese. At least as of 5 years ago, almost all stainless, excepting the real specialty and niche stuff, came from Japan.
workinwifdakids wrote: We've thus far avoided the temptation to jack an entire forum.

But what the hell.
Standing for Truth, Justice, and the American Way!

Post Reply